Softnet Driver Issues

Probing guidelines

Address validation

Any hardware layer address you obtain for your device should be verified. For example, for ethernet check it with linux/etherdevice.h:is_valid_ether_addr()

Close/stop guidelines

Quiescence

After the ndo_stop routine has been called, the hardware must not receive or transmit any data. All in flight packets must be aborted. If necessary, poll or wait for completion of any reset commands.

Auto-close

The ndo_stop routine will be called by unregister_netdevice if device is still UP.

Transmit path guidelines

Stop queues in advance

The ndo_start_xmit method must not return NETDEV_TX_BUSY under any normal circumstances. It is considered a hard error unless there is no way your device can tell ahead of time when its transmit function will become busy.

Instead it must maintain the queue properly. For example, for a driver implementing scatter-gather this means:

static u32 drv_tx_avail(struct drv_ring *dr)
{
        u32 used = READ_ONCE(dr->prod) - READ_ONCE(dr->cons);

        return dr->tx_ring_size - (used & bp->tx_ring_mask);
}

static netdev_tx_t drv_hard_start_xmit(struct sk_buff *skb,
                                       struct net_device *dev)
{
        struct drv *dp = netdev_priv(dev);
        struct netdev_queue *txq;
        struct drv_ring *dr;
        int idx;

        idx = skb_get_queue_mapping(skb);
        dr = dp->tx_rings[idx];
        txq = netdev_get_tx_queue(dev, idx);

        //...
        /* This should be a very rare race - log it. */
        if (drv_tx_avail(dr) <= skb_shinfo(skb)->nr_frags + 1) {
                netif_stop_queue(dev);
                netdev_warn(dev, "Tx Ring full when queue awake!\n");
                return NETDEV_TX_BUSY;
        }

        //... queue packet to card ...

        netdev_tx_sent_queue(txq, skb->len);

        //... update tx producer index using WRITE_ONCE() ...

        if (!netif_txq_maybe_stop(txq, drv_tx_avail(dr),
                                  MAX_SKB_FRAGS + 1, 2 * MAX_SKB_FRAGS))
                dr->stats.stopped++;

        //...
        return NETDEV_TX_OK;
}

And then at the end of your TX reclamation event handling:

//... update tx consumer index using WRITE_ONCE() ...

netif_txq_completed_wake(txq, cmpl_pkts, cmpl_bytes,
                         drv_tx_avail(dr), 2 * MAX_SKB_FRAGS);

Lockless queue stop / wake helper macros

The netif_txq_maybe_stop() and __netif_txq_completed_wake() macros are designed to safely implement stopping and waking netdev queues without full lock protection.

We assume that there can be no concurrent stop attempts and no concurrent wake attempts. The try-stop should happen from the xmit handler, while wake up should be triggered from NAPI poll context. The two may run concurrently (single producer, single consumer).

The try-stop side is expected to run from the xmit handler and therefore it does not reschedule Tx (netif_tx_start_queue() instead of netif_tx_wake_queue()). Uses of the stop macros outside of the xmit handler may lead to xmit queue being enabled but not run. The waking side does not have similar context restrictions.

The macros guarantee that rings will not remain stopped if there’s space available, but they do not prevent false wake ups when the ring is full! Drivers should check for ring full at the start for the xmit handler.

All descriptor ring indexes (and other relevant shared state) must be updated before invoking the macros.

No exclusive ownership

An ndo_start_xmit method must not modify the shared parts of a cloned SKB.

Timely completions

Do not forget that once you return NETDEV_TX_OK from your ndo_start_xmit method, it is your driver’s responsibility to free up the SKB and in some finite amount of time.

For example, this means that it is not allowed for your TX mitigation scheme to let TX packets “hang out” in the TX ring unreclaimed forever if no new TX packets are sent. This error can deadlock sockets waiting for send buffer room to be freed up.

If you return NETDEV_TX_BUSY from the ndo_start_xmit method, you must not keep any reference to that SKB and you must not attempt to free it up.